For California Consumers

Enter our Monthly draw to win a FREE Fresh Air LA-3500 v.2.0 Living Lightning™ Alpine Air purifier.

Name:
E-mail Address:
Submit your name and email address to subscribe to our private, valuable Health Tips Newsletter, and your name will be entered instantly in our Monthly draw to Win a FREE Fresh Air LA-3500 v.2.0 Living Lightning™ Alpine Air purifier!
* Please use your real name as winners are required to prove their identity. Your contact information will never be sold or rented to anybody, and you can opt-out at any time.
Click Here to email your friend a link to this site

How do I replace the fan motor in my new air purifier?

FAN MOTOR replacement instructions for all new models:
LA-2000 to Classic LA-3500 (Model #: E300/RH02; 300/RH02; 300/H02; 300/UH02; HL2PRO; ZL-3500/UV)

NOTE: First, make sure the unit has been unplugged and turned OFF!

  1. Dismantle the front panel grill

    Loosen the four screws fixing the grill of the front panel, then remove the grill.

  2. Dismantle the knobs

    Loosen the screws fixing the knobs with a small flat head screwdriver, proceed to remove the knobs.

  3. Remove the back Hepa filter

    Loosen the two screws on the back which attach the Hepa filter to the cabinet (housing). Now you can remove the Hepa filter, the photo catalytic metallic filter (if applicable to your model) and the ozone plates.

  4. Dismantle the housing

    Carefully flip the air purifier upside down and set it on hard surface. Loosen and remove the two bottom screws. Now you can remove the housing.

  5. Remove front metal bar

    Remove the two screws holding the front metal bar in place.

  6. Remove the fan blade

    Carefully pull the fan blade towards you rocking it side to side, so when you pull it out it won't hit the two ionizer prongs in front of it.

  7. Dismantle the support bar

    Loosen the four screws fixing the support bars, proceed to remove the support bar.

  8. Loosen the wires

    Cut the bundling strings to loosen the wires.

  9. Remove the fan wire

    Locate the wire connected to the fan motor on the PCB panel board. The slot with the plug is named "fun".

  10. Remove the fan motor

    Use a screw driver to remove the screws from the motor. Use pliers to hold the bolts in place while you're unscrewing the screw.

Now you should be able to completely remove the fan motor and replace it with a new fan motor. Then, just carefully follow directions in reverse to re-assemble the air purifier.

FAN MOTOR replacement instructions for all new models:
LA-1000 and LA-1500 (Model #: E300/A; 300/A)

NOTE: First, make sure the unit has been unplugged and turned OFF!

  1. Dismantle the front panel grill

    Loosen the four screws fixing the grill of the front panel, then remove the grill.

  2. Dismantle the knobs

    Loosen the screws holding the knobs in place with a small flat head screwdriver, then proceed to remove the knobs.

  3. Dismantle the housing

    Carefully flip the air purifier upside down and set it on hard surface. Loosen and remove the two bottom screws. Now you can remove the housing.

  4. Remove the glued white wire from the air intake

    Use a flat head screwdriver to carefully pry the wire from the air intake which is glued to the air intake.

  5. Dismantle the connections

    Cut the bundling string to loosen the wires. Locate the red/black fan wire that is plugged into the socket and carefully remove the wire from the socket.

  6. Dismantle the fan and air intake

    Loosen the screws and remove the fan and air intake.

  7. Install new fan

    Plug the wire of the new fan into the corresponding socket on the PCB panel.

Follow directions in reverse to re-assemble the air purifier.

* Make sure to use a glue gun or adhesive to keep the wire on the air intake affixed to the side so it does not move.